Instrument panel components - removal and refitting

1 Remove the instrument panel.

Panel illumination and warning lamp bulbs
2 Twist the relevant bulbholder anticlockwise and withdraw it from the printed circuit board on the rear of the instrument panel.

3 The bulbs may be either a push-fit in the bulbholder, or integral with the bulbholder in which case the bulb and bulbholder must be renewed as a unit (see illustrations).

21.3a Removing an instrument panel warning lamp bulb - bulb is a push-fit in
21.3a Removing an instrument panel warning lamp bulb - bulb is a push-fit in the bulbholder

21.3b Removing an instrument panel illumination bulb - bulb is integral with
21.3b Removing an instrument panel illumination bulb - bulb is integral with bulbholder

4 Refitting is a reversal of removal.

Panel lens
5 Remove the three upper and three lower securing screws and withdraw the lens from the instrument panel.

6 Refitting is a reversal of removal, but ensure that the two locating pegs on the upper corners of the instrument panel protrude through the lens, and locate the lugs on the lower edge of the lens in the cut-outs in the instrument panel.

Printed circuit board
7 Using a thin-bladed screwdriver, unclip and remove the wiring plug socket.

8 Remove all the illumination and warning lamp bulbs as described earlier in this Section.

9 Remove all the nuts and washers from the printed circuit board terminals.

10 Unclip the printed circuit board from the retainers at the back of the instrument panel, and carefully withdraw the board over the terminal pins on the gauges.

11 Refitting is a reversal of removal.

Speedometer
12 Remove the panel lens (paras. 5 and 6).

13 Remove the two screws securing the speedometer to the rear of the instrument panel, taking care not to lose the two brushes.

Withdraw the speedometer through the front of the instrument panel.

14 Refitting is a reversal of removal.

Tachometer
Models up to 1990
15 Remove the four or five securing screws, as applicable, and separate the two halves of the instrument panel housing.

16 Remove the three securing nuts and washers from the rear of the instrument panel housing, and withdraw the tachometer.

17 Refitting is a reversal of removal, but ensure that the tachometer engages with the locating ribs in the housing around the dial edge.

Models from 1990
18 The procedure is as described above but before the tachometer can be withdrawn from the instrument panel housing, the printed circuit board must be carefully pulled from the tachometer terminals. Ensure that the printed circuit board is pushed fully home when refitting.

Fuel and temperature gauges Models up to 1987
19 Remove the four securing screws and separate the two halves of the instrument panel housing.

20 Remove the four securing nuts and washers from the rear of the instrument panel housing, and withdraw the combined gauge assembly.

21 Refitting is a reversal of removal.

Models from 1987
22 Remove the five securing screws and separate the two halves of the instrument panel housing.

23 Remove the printed circuit board as described previously in this Section.

24 On low specification models, remove the two securing screws from the front of the gauge assembly, then withdraw the combined gauge assembly from the printed circuit board.

25 On high specification models, simply withdraw the combined gauge assembly from the printed circuit board.

26 Refitting is a reversal of removal, but on high specification models, ensure that the gauge assembly engages with the locating ribs in the housing around the gauge edge.

    See also:

    Changing a fuse
    WARNINGS: Do not modify the electrical system of your vehicle in any way. Have repairs to the electrical system and the replacement of relays and high current fuses carried out by properly traine ...

    Keyless entry
    General information WARNING: The keyless entry system may not function if the key is close to metal objects or electronic devices such as mobile phones. Note: If the door handles are pulled rep ...

    Rear window wiper and washers
    Intermittent wipe Pull the lever towards the steering wheel. Reverse gear wipe The rear wiper will be activated automatically when selecting reverse gear if: the rear wiper is not already sw ...