Manual climate control

Recommended settings for cooling
Recommended settings for cooling

Open the centre and side air vents.

Direct the centre air vents upwards and the side air vents toward the side windows.

Recommended settings for heating
Recommended settings for heating

Close the centre air vents and open the side air vents.

Direct the side air vents toward the side windows.

See Manual climate control.

Automatic climate control

Recommended settings for cooling
Recommended settings for cooling

Set the temperature to 22°C (72°F).

Open the centre and side air vents.

Direct the centre air vents upwards and the side air vents toward the side windows.

Recommended settings for heating
Recommended settings for heating

Set the temperature to 22°C (72°F).

Open the centre and side air vents.

Direct the centre air vents upwards and the side air vents toward the side windows.

See Automatic climate control.

Autolamps
Autolamps

The headlamps will come on and go off automatically depending on the ambient light.

See Lighting control.

Direction indicators
Direction indicators

If the lever is tapped up or down, the direction indicators will flash three times.

See Direction indicators.

Autowipers
Autowipers

Move the lever up one position.

The rain sensor will continuously measure the amount of water on the windscreen and adjust the speed of the front wipers automatically.

Adjust the sensitivity of the rain sensor using the rotary control.

See Windscreen wipers.

Airbag

WARNING:


WARNING:
To avoid the risk of death or serious injury, never use a rearward facing child restraint in the front, unless the air bag is off.

See Child safety.

See Disabling the passenger airbag.

Manual seats

Folding the seatback forwards - 3-door
Folding the seatback forwards - 3-door

1. Pull the locking lever to release the seatback.

Note: Do not hold the locking lever.

2. Push the seatback forwards to lock it in the folded position.

3. Continue to push the seatback to slide the seat forwards.

Returning the seatback to the seating position - 3-door
Returning the seatback to the seating position - 3-door

WARNING:
Do not place any objects behind the seatback which could prevent the engagement of the seat lock.

1. Slide the seat backwards to the end stop (memory position) or desired forward seating position.

Note: The memory function is only available on the driver's seat.

2. Pull the locking lever to release the seatback.

3. Unfold the seatback until it locks with a distinct click.

See Manual seats.

Fuel filler flap

WARNINGS:
Take care when refuelling to avoid spilling any residual fuel from the fuel pipe nozzle.

WARNINGS:
We recommend that you wait at least 10 seconds before removing the fuel pipe nozzle to allow any residual fuel to drain into the fuel tank.

Press the flap to open it. Open the flap


Press the flap to open it. Open the flap fully until it engages.

When you insert the fuel pipe nozzle, a spring loaded inhibitor will open if the correct size nozzle is detected. This will prevent filling up with the wrong fuel.

Insert the fuel pipe nozzle up to the first


Insert the fuel pipe nozzle up to the first notch on the nozzle, and keep it in position on the fuel filler opening.

See Fuel filler flap.

    See also:

    Crankshaft front oil seal - renewal
    1.8 litre (R2A type) 1 Remove the timing belt and the crankshaft sprocket and thrustwasher. 2 Withdraw the oil seal using an oil seal removal tool or by drilling the oil seal outer face and using ...

    Cylinder head - removal and refitting (engine in vehicle)
    Note: Refer to the note at the beginning of Section 20 before proceeding. 1.8 litre (R2A type) Removal 1 Disconnect the battery negative lead. 2 Drain the cooling system. 3 Disconnect the heater ...

    Rear under floor storage
    Vehicles with a sliding loadspace floor Raise the loadspace floor to gain access to the storage compartment. See Sliding loadspace floor. Vehicles without a sliding loadspace floor ...