Specifications
Battery
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . 12 volt lead-acid, 35 to 52 Ah depending on model
Charge condition:
Poor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 12.4 volts or less
Normal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 12.6 volts
Good . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 12.7 volts or over
Alternator
Minimum brush length:
Bosch, Lucas and Mitsubishi . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . 5.0 mm
Motorola . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . 4.0 mm
Regulator voltage at 4000 rpm with 3 to 7A load (all models) . . . . . . . .
13.7 to 14.6 volts
Starter motor
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . Pre-engaged
Make:
Bosch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 0.8 kW, 0.85 kW, 0.9 kW, 0.95 kW
Lucas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 8M 90, 9M 90, M 79
Nippondenso . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . 0.6 kW, 0.9 kW
Minimum brush length:
Bosch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . 10.0 mm
Lucas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 8.0 mm
Nippondenso 0.6 kW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . 10.0 mm
Nippondenso 0.9 kW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . 9.0 mm
See also:
Fuel computer components - removal and refitting
Computer unit
Removal
1 Disconnect the battery negative terminal.
2 Undo the two instrument panel bezel
retaining screws and ease the bezel out to
release the lower clips.
3 Withdraw the compute ...
Seats - removal and refitting
Front seat
1 Slide the seat fully forwards, and on seats
with height adjustment unhook the tension
spring from the rear crosstube. Where
applicable, disconnect the wiring from the
seat heating pa ...
ESC Hybrid system components - removal and refitting
Note: Procedures for removal and refitting of
the ignition system components and
electronic module are given elsewhere in the
relevant Sections of this Chapter.
1 Disconnect the battery negative l ...