Thermostat - removal and refitting

1 Disconnect the battery negative lead.

2 Drain the cooling system.

3 Proceed as follows according to model: SOHC models
4 Disconnect the radiator top hose and expansion tank hose from the thermostat housing situated at the front of the cylinder head (see illustrations).

7.4a Radiator top hose connection at thermostat housing
7.4a Radiator top hose connection at thermostat housing

7.4b Disconnect the expansion tank hose from the thermostat housing
7.4b Disconnect the expansion tank hose from the thermostat housing

5 Unscrew the two securing bolts and remove the housing and gasket.

6 Using a screwdriver, prise the retaining clip from the housing, and extract the thermostat and sealing ring (see illustrations).

7.6a Prise out the retaining clip . . .
7.6a Prise out the retaining clip . . .

7.6b . . . and extract the thermostat . . .
7.6b . . . and extract the thermostat . . .

7.6c . . . and sealing ring
7.6c . . . and sealing ring

7 Refitting is a reversal of removal, bearing in mind the following points.

8 Clean the housing and the mating face of the cylinder head. Check the thermostat sealing ring for condition and renew it if necessary. Use a new gasket when refitting the housing.

9 The thermostat wax capsule must face into the cylinder head with the flow direction arrow facing forward (see illustration).

7.9 Thermostat flow direction markings (arrowed)
7.9 Thermostat flow direction markings (arrowed)

10 Refill the cooling system.

CVH models
11 Disconnect the wiring plug from the cooling fan switch on the thermostat housing situated at the front of the inlet manifold.

12 Disconnect the automatic choke hose, radiator top hose and expansion tank hose from the thermostat housing. Where applicable, take care not to strain the wiring which is routed around the housing. If necessary, disconnect the wiring connector (see illustrations).

7.12a Disconnect the automatic choke hose . . .
7.12a Disconnect the automatic choke hose . . .

7.12b . . . the radiator top hose . . .
7.12b . . . the radiator top hose . . .

7.12c . . . and the expansion tank hose
7.12c . . . and the expansion tank hose

13 Unscrew the three securing bolts and remove the housing and gasket (see illustration).

7.13 Removing the thermostat housing and gasket
7.13 Removing the thermostat housing and gasket

14 Lift the thermostat from the housing, and carefully prise out the sealing ring.

15 Refitting is a reversal of removal, bearing in mind the following points.

16 Clean the housing and the mating face of the inlet manifold. Check the thermostat sealing ring for condition and renew it if necessary. Use a new gasket when refitting the housing.

17 Note that the thermostat wax capsule must face into the inlet manifold, with the flow direction arrow pointing forward, in line with the pressure relief valve in the housing (see illustration).

7.17 Correct orientation of thermostat with flow direction arrow pointing
7.17 Correct orientation of thermostat with flow direction arrow pointing towards pressure relief valve

18 Refill the cooling system.

DOHC models
19 On fuel injection models, for access to the thermostat housing loosen the clips and remove the air inlet tube which connects the plenum chamber to the inlet manifold.

20 Disconnect the coolant hoses from the thermostat housing (see illustrations).

7.20a Disconnect the coolant hoses . . .
7.20a Disconnect the coolant hoses . . .

7.20b . . . from the thermostat housing
7.20b . . . from the thermostat housing

21 Disconnect the wiring plug from the cooling fan switch mounted in the thermostat housing (see illustration).

7.21 Disconnect the cooling fan switch wiring plug
7.21 Disconnect the cooling fan switch wiring plug

22 Unscrew the three securing bolts, and withdraw the thermostat housing (see illustration).

7.22 Withdrawing the thermostat housing
7.22 Withdrawing the thermostat housing

23 Manipulate the thermostat from the inlet manifold, and recover the O-ring. If it is necessary to prise the thermostat out, take care not to damage the surface of the housing in the inlet manifold.

24 Refitting is a reversal of removal, bearing in mind the following points.

25 Ensure that the O-ring seal is correctly fitted around the edge of the thermostat.

26 When fitting the thermostat to the inlet manifold, ensure that the relief valve is located in the 12 oclock position (see illustration).

7.26 Thermostat relief valve (arrowed) should be in the 12 oclock position
7.26 Thermostat relief valve (arrowed) should be in the 12 oclock position

27 Tighten the thermostat housing securing bolts to the specified torque.

28 Refill the cooling system.

    See also:

    Changing a road wheel
    Locking wheel nuts You can obtain a replacement locking wheel nut key and replacement locking wheel nuts from your dealer using the reference number certificate. Vehicles with a temporary spare ...

    Rear suspension and axle assembly (P100 models) - removal and refitting
    Note: All self-locking nuts and spring washers must be renewed on reassembly. Removal 1 Chock the front wheels, jack up the rear of the vehicle and support on axle stands placed under the side me ...

    Catalytic converter
    WARNING: Do not park or idle your vehicle over dry leaves, dry grass or other combustible materials. The exhaust will radiate a considerable amount of heat during use, and after you have switched ...